Rosemount 848T Especificações Página 41
- Página / 136
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
33
Reference Manual
00809-0100-4697, Rev GA
Section 3: Configuration
November 2014
Configuration
FAILED_PRI
Designates the alerting priority of the FAILED_ALM, see Table 3-4 on page 31. The default is
0 and the recommended value are between 8 and 15.
FAILED_ACTIVE
This parameter displays which of the alarms is active. Only the alarm with the highest
priority will be displayed. This priority is not the same as the FAILED_PRI parameter
described above. This priority is hard coded within the device and is not user configurable.
FAILED_ALM
Alarm indicating a failure within a device which makes the device non-operational.
MAINT_ALARMS
A maintenance alarm indicates the device or some part of the device needs maintenance soon.
If the condition is ignored, the device will eventually fail. There are five parameters associated
with MAINT_ALARMS, they are described below.
MAINT_ENABLED
The MAINT_ENABLED parameter contains a list of conditions indicating the device or some
part of the device needs maintenance soon.
Table 3-6. Maintenance Alarms/Priority Alarm
MAINT_MASK
The MAINT_MASK parameter will mask any of the failed conditions listed in
MAINT_ENABLED. A bit on means that the condition is masked out from alarming and will
not be reported.
MAINT_PRI
MAINT_PRI designates the alarming priority of the MAINT_ALM, Table 3-4 on page 31. The
default is 0 and the recommended values is 3 to 7.
Alarm Priority
CJC Degraded 1
Body Temperature Out of Range 2
Sensor 1 Degraded 3
Sensor 2 Degraded 4
Sensor 3 Degraded 5
Sensor 4 Degraded 6
Sensor 5 Degraded 7
Sensor 6 Degraded 8
Sensor 7 Degraded 9
Sensor 8 Degraded 10
- Transmitter with FOUNDATION 1
- fieldbus 1
- Transmitter with F 3
- Title Page 4
- 1Section 1: Introduction 5
- 2Section 2: Installation 5
- 3Section 3: Configuration 5
- AAppendix A: Reference Data 6
- DAppendix D: Function Blocks 8
- Section 1 Introduction 9
- 00809-0100-4697, Rev GA 10
- November 2014 10
- OUNDATION fieldbus Technology 10
- 1.3 Service support 11
- Section 1: Introduction 12
- Introduction 12
- Section 2 Installation 13
- 2-in. screws 14
- 2.3 Wiring 16
- RTD or ohm inputs 17
- Analog inputs 17
- 2.4 Grounding 19
- Shielded wire 20
- Grounded thermocouple inputs 21
- Analog device inputs 21
- 2.5 Switches 22
- 2.6 Tagging 22
- Transmitter tag 23
- Sensor tag 23
- 2.7 Installation 24
- 2.7.2 Using conduit entries 25
- Section 2: Installation 26
- Section 3 Configuration 27
- 3.2 Configuration 28
- 3.2.5 Alarms 29
- 3.2.6 Damping 29
- Typical profiling application 31
- OUNDATION fieldbus 33
- Section 3: Configuration 34
- Number Parameter Description 34
- OUNDATION 35
- How to use PlantWeb Alarm 39
- 3.4.3 PlantWeb alerts 40
- MAINT_ALARMS 41
- Advisory alarms 42
- RECOMMENDED_ACTION 43
- FD failed alarms 44
- Configuration 45
- FD CHECK ALARMS 47
- 3.4.7 Transducer blocks 49
- Transducer block errors 50
- Transducer block modes 50
- Automatic (Auto) 51
- Out of Service (OOS) 51
- 4.4.2 Resource block 64
- Appendix A Reference Data 65
- OUNDATION fieldbus parameters 66
- A.3 Function blocks 67
- A.4.1 Stability 68
- A.4.2 Self calibration 68
- A.4.3 Vibration effect 68
- A.4.5 Accuracy 68
- A.4.8 Analog sensors 4–20mA 69
- Reference Data 70
- Examples 71
- A.5 Dimensional drawings 72
- A.5.1 Mounting options 74
- A.6 Ordering information 75
- Approvals 77
- B.3.2 Canada 78
- B.4 Europe 79
- B.5 International 81
- B.5.1 Brazil 83
- B.5.2 China 84
- B.5.3 Japan 86
- B.6 Combinations 87
- B.8 Additional Certifications 88
- B.10 Installation drawings 90
- Product Certificates 91
- Appendix C FOUNDATION 99
- Technology 99
- C.3 Device descriptions 100
- C.4 Block operation 101
- C.5 Network communication 101
- C.5.1 LAS 102
- C.5.2 Addressing 103
- C.5.3 Scheduled transfers 104
- C.5.4 Unscheduled transfers 105
- OUNDATION Fieldbus Technology 106
- Appendix D Function Blocks 107
- Reference Manual 108
- Appendix D: Function Blocks 108
- Table 3-5 on page 11 108
- D.1.1 Functionality 110
- Filtering 111
- Signal conversion 111
- Indirect 111
- Indirect square root 112
- Block errors 112
- Alarm detection 113
- Status handling 114
- Advanced features 114
- Application information 114
- D.2.1 Functionality 118
- D.3.1 Functionality 125
- Block execution 127
- AVG_USE = 6 129
- Numerics 131
Manuais e produtos relacionados com Medição, teste e controlo Rosemount 848T
(36 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.029 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais