Rosemount 848T Especificações Página 84
- Página / 136
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
76
Reference Manual
00809-0100-4697, Rev GA
Appendix B: Product Certifications
November 2014
Product Certificates
Special Conditions of Safe Use:
1. The equipment must be installed in an enclosure that provides a degree of
protection of at least IP20 and which is appropriate to the application specified in
ABNT NBR IEC60079-0.
2. The equipment is not capable of withstanding the dielectric strength test of
500V according to item 6.3.12 of ABNT NBR IEC60079-1, this should be
considered in the installation, see installation manual.
N2 INMETRO Intrinsic Safety Zone 2
Certificate: NCC 12.1182X
Standards: ABNT NBR IEC 60079-0:2008 Versao corrigida 2011, ABNT NBR IEC
60079-11:2009
Markings: Ex ic IIC T5 (-40°C ≤ T
a
≤ +65 °C) Gc
Special Conditions of Safe Use:
1. The equipment must be mounted within an enclosure that meets at least the
degree of protection IP54, with material and manufacture covered by a quality
certificate. If the enclosure is non-metallic, the enclosure must have a surface
resistance less than 1 GÙ. If the enclosure is made of zirconium alloy, the
enclosure must be protected against impact and friction when installed.
2. Provision must be made, external to the equipment, to ensure that the supply
voltage (42.2Vdc) is not exceeded by transient disturbances of more than 40%.
3. The maximum ambient temperature will be restricted to lowest temperature
rating of the equipment, cables, cables glands or plugs.
4. The electric circuit is connected directly to ground, this should be taken into
account when installing the equipment.
B.5.2 China
I3 NEPSI Intrinsic Safety
Certificate: GYJ111365X
Standards: GB3836.1-2000, GB3836.4-2000
Markings: Ex ia IIC T4
Special Conditions for Safe Use (X):
1. Only when temperature transmitter is installed in IP 20(GB4208-2008) housing,
can it be used in a hazardous location. Metallic housing should observe the
requirements of GB3836.1-2000 Clause 8. Non-metallic housing should observe
the requirements of GB3836.1-2000 Clause 7.3.
Table B-7. INMETRO-B Entity Parameters
FISCO (Input)
Sensor Field Terminal
(Output)
U
i
=17.5 Vdc U
o
= 12.5 Vdc
I
i
= 380 mA I
o
= 4.8 mA
P
i
= 5.32 W P
o
= 15 mW
C
i
= 2.1 nF C
o
= 1.2 mF
L
i
= 0 L
o
= 1 H
- Transmitter with FOUNDATION 1
- fieldbus 1
- Transmitter with F 3
- Title Page 4
- 1Section 1: Introduction 5
- 2Section 2: Installation 5
- 3Section 3: Configuration 5
- AAppendix A: Reference Data 6
- DAppendix D: Function Blocks 8
- Section 1 Introduction 9
- 00809-0100-4697, Rev GA 10
- November 2014 10
- OUNDATION fieldbus Technology 10
- 1.3 Service support 11
- Section 1: Introduction 12
- Introduction 12
- Section 2 Installation 13
- 2-in. screws 14
- 2.3 Wiring 16
- RTD or ohm inputs 17
- Analog inputs 17
- 2.4 Grounding 19
- Shielded wire 20
- Grounded thermocouple inputs 21
- Analog device inputs 21
- 2.5 Switches 22
- 2.6 Tagging 22
- Transmitter tag 23
- Sensor tag 23
- 2.7 Installation 24
- 2.7.2 Using conduit entries 25
- Section 2: Installation 26
- Section 3 Configuration 27
- 3.2 Configuration 28
- 3.2.5 Alarms 29
- 3.2.6 Damping 29
- Typical profiling application 31
- OUNDATION fieldbus 33
- Section 3: Configuration 34
- Number Parameter Description 34
- OUNDATION 35
- How to use PlantWeb Alarm 39
- 3.4.3 PlantWeb alerts 40
- MAINT_ALARMS 41
- Advisory alarms 42
- RECOMMENDED_ACTION 43
- FD failed alarms 44
- Configuration 45
- FD CHECK ALARMS 47
- 3.4.7 Transducer blocks 49
- Transducer block errors 50
- Transducer block modes 50
- Automatic (Auto) 51
- Out of Service (OOS) 51
- 4.4.2 Resource block 64
- Appendix A Reference Data 65
- OUNDATION fieldbus parameters 66
- A.3 Function blocks 67
- A.4.1 Stability 68
- A.4.2 Self calibration 68
- A.4.3 Vibration effect 68
- A.4.5 Accuracy 68
- A.4.8 Analog sensors 4–20mA 69
- Reference Data 70
- Examples 71
- A.5 Dimensional drawings 72
- A.5.1 Mounting options 74
- A.6 Ordering information 75
- Approvals 77
- B.3.2 Canada 78
- B.4 Europe 79
- B.5 International 81
- B.5.1 Brazil 83
- B.5.2 China 84
- B.5.3 Japan 86
- B.6 Combinations 87
- B.8 Additional Certifications 88
- B.10 Installation drawings 90
- Product Certificates 91
- Appendix C FOUNDATION 99
- Technology 99
- C.3 Device descriptions 100
- C.4 Block operation 101
- C.5 Network communication 101
- C.5.1 LAS 102
- C.5.2 Addressing 103
- C.5.3 Scheduled transfers 104
- C.5.4 Unscheduled transfers 105
- OUNDATION Fieldbus Technology 106
- Appendix D Function Blocks 107
- Reference Manual 108
- Appendix D: Function Blocks 108
- Table 3-5 on page 11 108
- D.1.1 Functionality 110
- Filtering 111
- Signal conversion 111
- Indirect 111
- Indirect square root 112
- Block errors 112
- Alarm detection 113
- Status handling 114
- Advanced features 114
- Application information 114
- D.2.1 Functionality 118
- D.3.1 Functionality 125
- Block execution 127
- AVG_USE = 6 129
- Numerics 131
Manuais e produtos relacionados com Medição, teste e controlo Rosemount 848T
(36 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais