Rosemount 848T Especificações Página 58
- Página / 136
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
50
Reference Manual
00809-0100-4697, Rev GA
Section 3: Configuration
November 2014
Configuration
Table 3-24. Validation Value Sub-parameter Structure
Table 3-25. Validation Config Sub-parameter Structure
Validation value sub-parameter structure
Parameter Description
VALIDATION_STATUS State of the channel specific measurement validation measurement
DEVIATION_VALUE Deviation output value
DEVIATION_STATUS Status of the deviation output
RATE_OF_CHANGE_VALUE Rate of change value output
RATE_OF_CHANGE_STATUS Status of Rate of change output
Parameter Description
VALIDATION_MODE
Activates the measurement validation data gathering process
0 = Disable
1 = Enable
SAMPLE_RATE
Number of seconds per sample used for measurement validation
data collection. This shouldn't exceed 10 seconds per sample, but
currently there are no upper limits.
DEVIATION_LIMIT
Sets the limit for the deviation diagnostic. DD limits the upper range
to 10.
DEVIATION_ENG_UNITS Units tied to the deviation output value
DEVIATION_ALERT_SEVERITY
Advisory, Maintenance, Failure
0 = Disabled = Does not use the limits, but provides an output
1 = Advisory = No effect on sensor status, sets advisory PWA
2 = Maint = Sets sensor status to uncertain, sets advisory PWA
3 = Failure = Sets sensor status to Bad, sets advisory PWA
DEVIATION_PCNT_LIM_HYST
Deviation Hysteresis Limit = (1 - DEVIATION_PCNT_LIM_HYST/100)
* DEVIATION_LIMIT
RATE_INCREASING_LIMIT Increasing Rate of Change limit set point
RATE_DECREASING_LIMIT Decreasing Rate of Change limit set point
RATE_ENG_UNITS Units tied to the rate of change output value
RATE_ALERT_SEVERITY
Advisory, Maintenance, Failure
0 = Disabled = Does not use the limits, but provides an output
1 = Advisory = No effect on sensor status, sets advisory PWA
2 = Maint = Sets sensor status to uncertain, sets advisory PWA
3 = Failure = Sets sensor status to Bad, sets advisory PWA
RATE_PCNT_LIM_HYST
Rate of Change Increasing Hysteresis Limit = (1 -
RATE_PCNT_LIM_HYST/100) * RATE_INCREASING_LIMIT
- Transmitter with FOUNDATION 1
- fieldbus 1
- Transmitter with F 3
- Title Page 4
- 1Section 1: Introduction 5
- 2Section 2: Installation 5
- 3Section 3: Configuration 5
- AAppendix A: Reference Data 6
- DAppendix D: Function Blocks 8
- Section 1 Introduction 9
- 00809-0100-4697, Rev GA 10
- November 2014 10
- OUNDATION fieldbus Technology 10
- 1.3 Service support 11
- Section 1: Introduction 12
- Introduction 12
- Section 2 Installation 13
- 2-in. screws 14
- 2.3 Wiring 16
- RTD or ohm inputs 17
- Analog inputs 17
- 2.4 Grounding 19
- Shielded wire 20
- Grounded thermocouple inputs 21
- Analog device inputs 21
- 2.5 Switches 22
- 2.6 Tagging 22
- Transmitter tag 23
- Sensor tag 23
- 2.7 Installation 24
- 2.7.2 Using conduit entries 25
- Section 2: Installation 26
- Section 3 Configuration 27
- 3.2 Configuration 28
- 3.2.5 Alarms 29
- 3.2.6 Damping 29
- Typical profiling application 31
- OUNDATION fieldbus 33
- Section 3: Configuration 34
- Number Parameter Description 34
- OUNDATION 35
- How to use PlantWeb Alarm 39
- 3.4.3 PlantWeb alerts 40
- MAINT_ALARMS 41
- Advisory alarms 42
- RECOMMENDED_ACTION 43
- FD failed alarms 44
- Configuration 45
- FD CHECK ALARMS 47
- 3.4.7 Transducer blocks 49
- Transducer block errors 50
- Transducer block modes 50
- Automatic (Auto) 51
- Out of Service (OOS) 51
- 4.4.2 Resource block 64
- Appendix A Reference Data 65
- OUNDATION fieldbus parameters 66
- A.3 Function blocks 67
- A.4.1 Stability 68
- A.4.2 Self calibration 68
- A.4.3 Vibration effect 68
- A.4.5 Accuracy 68
- A.4.8 Analog sensors 4–20mA 69
- Reference Data 70
- Examples 71
- A.5 Dimensional drawings 72
- A.5.1 Mounting options 74
- A.6 Ordering information 75
- Approvals 77
- B.3.2 Canada 78
- B.4 Europe 79
- B.5 International 81
- B.5.1 Brazil 83
- B.5.2 China 84
- B.5.3 Japan 86
- B.6 Combinations 87
- B.8 Additional Certifications 88
- B.10 Installation drawings 90
- Product Certificates 91
- Appendix C FOUNDATION 99
- Technology 99
- C.3 Device descriptions 100
- C.4 Block operation 101
- C.5 Network communication 101
- C.5.1 LAS 102
- C.5.2 Addressing 103
- C.5.3 Scheduled transfers 104
- C.5.4 Unscheduled transfers 105
- OUNDATION Fieldbus Technology 106
- Appendix D Function Blocks 107
- Reference Manual 108
- Appendix D: Function Blocks 108
- Table 3-5 on page 11 108
- D.1.1 Functionality 110
- Filtering 111
- Signal conversion 111
- Indirect 111
- Indirect square root 112
- Block errors 112
- Alarm detection 113
- Status handling 114
- Advanced features 114
- Application information 114
- D.2.1 Functionality 118
- D.3.1 Functionality 125
- Block execution 127
- AVG_USE = 6 129
- Numerics 131
Manuais e produtos relacionados com Medição, teste e controlo Rosemount 848T
(36 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.071 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais